Filament SUNLU High-Speed Matte PETG (red)

Price: 15,99 
Cijena na prvi dan u ponudi 20.11.2026.: 15,99 
Cijena prema načinu plaćanja Detalji
  • Gotovina / uplata na račun −10 % 14,39 
  • Kartice jednokratno −7 % 14,87 
  • Pouzeće −5 % 15,19 
  • Kartice na rate 15,99 
Šifra
749
EAN
6933582315313
Kataloški broj proizvođača
PETG H-S M R
Product availability: Dobavljivo kroz 10–14 radnih dana
Stanje u poslovnicama
  • Zagreb Po narudžbi
  • Varaždin Po narudžbi
  • Strmec, Sveta Nedelja Po narudžbi
Dijeli

SUNLU High-Speed Matte PETG Filament (red)

SUNLU High-Speed Matte PETG is a 3D printing filament that allows you to print at speeds ranging from 50 to as high as 600 mm/s while maintaining smooth extrusion and good surface quality. The increased fluidity of the molten material ensures smooth filament feeding during high-speed printing, while good layer adhesion and a design that minimizes the risk of nozzle clogging contribute to stable operation. The matte, low-gloss surface reduces reflections and gives models an aesthetic finish, making the material suitable for both functional and decorative prints. The filament diameter is 1.75 ±0.02 mm, and each spool contains 1 kg of material, approximately 330 m in length.

Red printing filament wound on a dark gray spool.

Up to 600 mm/s and a smooth, matte finish

High-Speed Matte PETG can be used at various print speeds—for 50–100 mm/s, the recommended nozzle temperature is 205–215°C; for 100–300 mm/s, it is 240–250°C; and for 300–600 mm/s, 260–270°C should be used. The material combines high printing speeds with good strength, flexibility, and resistance to impact, wear, and various chemicals, making it suitable for prototypes, functional parts, mechanical designs, and DIY projects, among other applications. The tensile strength is 48 MPa, the flexural strength is 78 MPa, and the elongation at break is 33%, which allows for the creation of durable models with good layer adhesion.

Colored filament spools along with printed decorative and mechanical parts on a desk.

Optimal Conditions for Stable Printing

The recommended bed temperature is 60–70°C; at 70–80°C, no adhesive is required; however, if using an unheated platform, adhesive must be applied. Due to its increased fluidity, PETG is more susceptible to moisture, which can cause stringing, material leakage, and a deterioration in print quality; therefore, the filament must be thoroughly dried before printing and protected from moisture during long print runs. The recommended humidity during storage and printing is below 20% RH when stored in an airtight container with a desiccant, and the drying setting is 50°C; for SUNLU S4/E2 dryers, 65°C for at least 8 hours is recommended.

A set of colored filament spools and finished printed objects of various shapes.

 

ManufacturerSUNLU
NameHigh-Speed Matte PETG
ColorRed
MaterialPETG
Filament Diameter1.75 ±0.02 mm
Print Speed50–600 mm/s
Nozzle temperature for 50–100 mm/s205–215°C
Nozzle temperature for 100–300 mm/s240–250°C
Nozzle temperature for 300–600 mm/s260–270°C
Bed temperature60–70°C
Bed temperature without adhesive70–80°C
Recommended humidity<20% RH
Drying temperature50°C
Recommended drying in SUNLU S4/E265°C for at least 8 hours
Density1.26 g/cm³
Heat deflection temperature70°C
Melting point128°C
Melt flow rate4.4 g/10 min
Tensile strength48 MPa
Elongation at break33%
Flexural strength78 MPa
Flexural modulus2700 MPa
IZOD impact strength (X-Y notch)4.1 kJ/m²
Net weight1 kg
Gross weight1.3 kg
Filament lengthApproximately 330 m

  • Marka
  • Referenca
    PETG H-S M R
  • Na skladištu
    100 Artikli
  • ean13
    6933582315313
  • MPN
    PETG H-S M R
Sigurno plaćanje
Kartične podatke obrađuje banka, mi ih ne vidimo.
Brza dostava
Artikli na lageru šalju se u 1–2 radna dana. Besplatna dostava iznad 200 €.
Povrat u 14 dana
Robu možete vratiti bez navođenja razloga.

Komentari (0)

Trenutno nema recenzija korisnika.

4 other products in the same category

Sunlu PLA+ Filament 2.0 (magenta)
19,99 
Gotovina / uplata na račun: 17,99 
Cijena na prvi dan u ponudi 20.11.2026.: 19,99 
Rated out of 5 stars based on review(s)
CR-PETG Filament Creality (Red)
16,79 
Gotovina / uplata na račun: 15,11 
Cijena na prvi dan u ponudi 20.11.2026.: 16,79 
Rated out of 5 stars based on review(s)
Filament eSun PLA-Basic 1.75mm 1kg (yellow)
19,99 
Gotovina / uplata na račun: 17,99 
Cijena na prvi dan u ponudi 20.11.2026.: 19,99 
Rated out of 5 stars based on review(s)
Sunlu ABS Filament (Silver)
18,39 
Gotovina / uplata na račun: 16,55 
Cijena na prvi dan u ponudi 20.11.2026.: 18,39 
Rated out of 5 stars based on review(s)

Pregledani proizvodi

ANYCUBIC Standard Resin (crimson clay)
18,39 
Gotovina / uplata na račun: 16,55 
Cijena na prvi dan u ponudi 20.11.2026.: 18,39 
Rated out of 5 stars based on review(s)
Revopoint Magnetic Markers (208 pcs.)
74,39 
Gotovina / uplata na račun: 66,95 
Cijena na prvi dan u ponudi 20.11.2026.: 74,39 
Rated out of 5 stars based on review(s)
Sunlu Filament Dryer for AMS Bambu Lab
134,39 
Gotovina / uplata na račun: 120,95 
Cijena na prvi dan u ponudi 20.11.2026.: 134,39 
Rated out of 5 stars based on review(s)
Učitavanje...
Povratak na vrh